SPECIFICATION產品描述
| Base 主成分 | Silicone Resin compound 矽基合成樹脂 |
| Color 顏色 | Straw Light 透明微黃 |
| Solids content 固成分 | ≦ 80 % |
| Temperature Resistance 耐溫范圍 | -50 to 200 °C |
| Viscosity 稠度(cps) | 200~350cps |
| Specific gravity 比重 | 1.05 |
| Tack free time 表干燥時間 | 25 ~30 min(0.1mm) |
| Full cure time 完全硬化時間 | 72 hrs |
| Flame self-extinguishing 防火等級 | UL94V-0 |
| Storage stability 保存期限 | 9 months |
| Elongation % 延展性 | >48 |
| Hardness Shore A 硬度 | >68 |
| Surface insulation resistance 表面阻抗 | 1×10 14 Ω.cm |
| Dielectric Strength KV/mm 介電強度 | >28 |
| Shearing strength kg/cm 2 剪斷強度 | >26 |
1. Ensure the coating surface are free from dirt, moisture, grease, habitant & waste particle.
請確定接著表面無灰塵、無水、無油漬、臟污物或是任何附著物。
2. Apply the material a smooth layer of HB-3188 with a spraying or dispensing. If thesurface is rough and uneven, ensure the glue has cover all gaps during coating process..
請用噴涂或點膠方式將 HB-3188 均勻涂布在電子產品上。若物品表面粗糙或是崎嶇不平須確定用本產品均勻且完全覆蓋所有表面。
3. The take free time about 30 minutes, but it not meaning cured, the fully cure time are 72hours (0.1mm). Due to this period please don’t squeezing or friction the surface toprevent product surface damage. When temperature is under 15°C the curing time will be ouble with above mention.
本產品涂布(約 0.1mm)后約 30 分鐘表面會干燥，但并不表示完全硬化，此時可以移動或進行包裝不會沾黏，但盡可能不要擠壓或磨擦表面防止破壞本產品。因涂布厚度不同會影響干燥時間，正常狀況下(厚度約 0.1mm)會在 72 小時候達到完全硬化狀態，當溫度低于 15 度時硬化時間會延??倍時間。
CAUTION注意
Use with adequate ventilation。
請?jiān)谕L(fēng)良好的地方進行使用，
Avoid skin contact, avoid prolonged breathing of vapors。
并避免碰觸皮膚與吸入揮發性氣體。
Use in area free from sparks and flame.
請遠離火源與火星。
Keep container tightly closed when not in using.
不使用時請密封保存。
PACKAGE 包裝方式
1KG/CAN 罐 & 18KG/DRUM 桶